Macrame Plant Hanger Diy No Ring (2023)

Reading Time: 7 minutes

Macrame plant hangers are a hot trend in home décor. They are a simple, inexpensive way to add a touch of organic style to any room. You can make your own macrame plant hanger without a ring, using just a few basic knots.

To make a macrame plant hanger without a ring, you will need:

-a piece of cord or rope, at least 3 yards long
-a plant hanger hook
-scissors

Start by cutting the cord or rope into two pieces, each measuring 3 yards in length. Knot one end of each piece of cord together, then knot the other end together. This will create a loop in the center of the cord.

Next, tie a simple loop knot around the plant hanger hook. This knot is also known as a “cow hitch” knot.

Now, we will start creating the body of the plant hanger. Take the left-hand piece of cord and make a braid. To do this, cross the cord over the middle cord, then take the right-hand piece of cord and place it over the left-hand piece. Now, take the left-hand piece and place it over the right-hand piece. Repeat this process, crossing the cord over the middle cord and taking the opposite piece of cord each time.

When you reach the end of the cord, tie a simple knot to secure it. Then, start braiding the other piece of cord in the same way.

Once both pieces of cord have been braided, tie a knot in the middle of the braid to create a hanger for your plant.

Your macrame plant hanger is now complete!

Materials Needed for DIY Macrame Plant Hanger without a Ring

Do you want to add a touch of natural beauty to your home without spending a lot of money? If so, you may want to consider making a macrame plant hanger. This project is relatively easy and can be completed in just a few hours. You will need some basic supplies, including cord or rope, scissors, and a plant hanger ring. However, you can also make a plant hanger without a ring if you prefer.

When making a macrame plant hanger without a ring, you will need to create a loop at the top of the hanger. This loop will be used to hang the hanger from a hook or nail. The loop can be made using a slip knot or another type of knot.

Once you have created the loop, you will need to determine the length of cord you will need for the hanger. To do this, measure the height of the plant hanger ring, plus the length of the cord you will use to create the hanger. Add an extra 10 inches to this measurement to allow for tying the knots.

Next, cut the cord to the desired length. You will then need to create a series of knots to form the hanger. There are a variety of knots that can be used for this project, but the basic knots you will need are the half hitch and the square knot.

To create the half hitch knot, tie a knot around the cord about an inch from the end. Then, tie a second knot around the cord an inch from the first knot. You should now have a loop in the cord.

To create the square knot, tie a knot around the cord about two inches from the end. Then, tie a second knot around the cord an inch from the first knot. Now, tie a third knot around the cord an inch from the second knot. You should now have a square knot.

Repeat these steps to create a series of knots along the length of the cord. When you reach the loop at the top, tie a final knot to secure it.

Your macrame plant hanger is now complete. Simply hang it from a hook or nail and add your favorite plant.

Step-by-Step Guide to Creating a Macrame Plant Hanger without a Ring

Macrame plant hangers are a fun and easy way to show off your plants. You can make them with or without a ring, and this tutorial will show you how to make a macrame plant hanger without a ring.

You will need:

-A piece of cord or rope at least 30 feet long
-Scissors
-A plant pot or container

To make a macrame plant hanger without a ring, you will first need to cut a piece of cord or rope at least 30 feet long. Then, fold the cord in half to find the center.

Next, tie a basic knot at the center of the cord. This is called a “square knot” and it’s the knot you will use for the rest of the project.

Now, you will need to measure out 18 inches from the center knot. This is where you will begin to create the hanger.

To create the hanger, tie a square knot around the pot or container. Make sure the knot is tight against the pot or container.

Then, continue tying square knots around the pot or container. The hanger will grow in size as you add more knots.

When you reach the end of the cord, tie a square knot to secure it. Then, cut off any excess cord.

Your macrame plant hanger is now complete!

Measuring and Cutting Cords for Macrame Plant Hanger

Macrame Plant Hanger Diy No Ring
Measure and Cut Cords for Macrame Plant Hanger

What you’ll need:

-Cord or rope in two different colors
-Scissors
-Tape measure
-Plant hanger

How to make it:

1. Cut one piece of cord or rope to measure 32 inches. Cut the other piece of cord or rope to measure 26 inches.

2. Tape the ends of the cords or ropes together to create one long piece.

3. Measure 6 inches from one end of the cord or rope and make a mark. This is where you will start knotting.

4. Make a loop with the cord or rope and tie a knot at the 6-inch mark.

5. Repeat steps 3 and 4 until you reach the end of the cord or rope.

6. Trim the ends of the knots so they are even.

7. Attach the plant hanger to the top of the macrame plant hanger.

Tying Basic Knots for Macrame Plant Hanger

Macrame plant hangers are a popular way to display plants in a home or office. They are simple to make and can be customized to fit any space.

There are a variety of knots that can be used to make a macrame plant hanger. The basic knots are the overhand knot, the half hitch, and the square knot.

To make a macrame plant hanger using the basic knots, you will need:

-A piece of cord or rope, at least 32 feet long
-Scissors
-A plant pot or container

1. Cut a piece of cord or rope, at least 32 feet long.

2. Fold the cord in half, so that it is 16 feet long.

3. Cut a small piece of cord, about 8 inches long.

4. Tie an overhand knot in the middle of the cord, using the small piece of cord.

5. Take the left strand of the cord, and cross it over the right strand.

6. Take the right strand of the cord, and cross it over the left strand.

7. Take the top strand of the cord, and cross it over the bottom strand.

8. Take the bottom strand of the cord, and cross it over the top strand.

9. Pull on all of the strands to tighten the knot.

10. Repeat steps 5-9 until you have reached the desired length for your plant hanger.

11. Tie a square knot at the end of the cord, using the small piece of cord.

12. Cut the excess cord, and tie a half hitch knot to secure it.

13. Trim the excess cord, if necessary.

14. Slip the plant pot or container onto the hanger, and hang it in a desired location.

Creating the Macrame Design for Plant Hanger without a Ring

Macrame is a type of knotting that is often used to create decorative items. While it can be used to create items with a ring, it is also possible to create a macrame plant hanger without a ring. This involves creating a design for the hanger that will hold the plant in place.

The first step in creating a macrame plant hanger without a ring is to create the basic design. This design will consist of a series of basic knots that will be used to create the hanger. There are a variety of different knots that can be used for this purpose, but the simplest knot is the basic knot. This knot is made by tying a simple knot in the thread and then tightening it.

Once the basic knot is mastered, the next step is to create the hanger. This will involve creating a series of loops with the thread. These loops can be created in any pattern that is desired. Once the loops are created, they can be joined together to create the hanger.

The final step is to add the plant. This can be done by placing the plant in the center of the hanger and then wrapping the thread around it. The thread can be wrapped around the plant a few times to secure it in place.

Finishing and Securing the Macrame Plant Hanger

There are many ways to finish a macrame plant hanger. In this tutorial, you will learn how to finish a plant hanger without a ring, and how to secure the hanger to the pot.

To finish the hanger, you will need:

– scissors
– a piece of cord or twine
– a needle

The first step is to cut the cord or twine to the desired length. Next, tie a knot at one end of the cord.

Thread the needle and tie a knot at the other end of the cord. Push the needle through the loop created by the knot.

Pull the needle and the cord through the loop, until the knot is tight against the cord. Cut off the excess cord.

To secure the hanger to the pot, you will need:

– a piece of wire
– pliers

Bend the wire into a U-shape. Twist the ends of the wire together, to create a loop.

Slide the loop over the top of the pot. Twist the ends of the wire together, to create a second loop.

Use the pliers to twist the ends of the wire together, to create a secure closure.

Hanging and Displaying the DIY Macrame Plant Hanger

Macrame plant hangers are a great way to add a touch of nature to any room. They can also be used to display plants that may not otherwise have a place to grow. This article will show you how to make a DIY macrame plant hanger without a ring.

The supplies you will need for this project include:

-A piece of cord measuring about 6 feet long
-A piece of cord measuring about 18 inches long
-A plant hanger ring
-Scissors
-A tape measure

To make the hanger, first cut the 6-foot piece of cord in half. Take one of the halves and fold it in half so that it forms a loop. Then, use the scissors to cut a small hole in the center of the loop. This will be the top of the hanger.

Next, measure 2 feet from the top of the hanger and make a small mark. This is where the hanger will need to be attached to the plant hanger ring.

Take the 18-inch piece of cord and tie a knot around the top of the hanger. Make sure the knot is tight and secure. Then, use the scissors to cut off any excess cord.

Thread the other half of the cord through the plant hanger ring and make a knot at the other end. Again, make sure the knot is tight and secure.

Your DIY macrame plant hanger is now finished! Simply hang it on a hook in the desired location and add your favorite plants.